완성된 철통에 나사산 플러그를 설치했을 때 플랜지 나사산이 손상되어 플러그를 조일 수 없는 경우에는 어떻게 합니까?
Drum flange is a common closure device for tight head steel pail or steel drum. What if the flange thread was damaged due to the failure of the flange locking die, resulting in damage to the inner thread of the flange, and the plug cannot be screwed in. What should be done?
답변:
This situation is actually a relatively common problem in barrel-making enterprises. Under normal circumstances, problems should be discovered early in the flange locking process, and the mold or equipment should be repaired in time to avoid greater losses. When the steel drum is finished, it is found that the flange thread is damaged. It is indeed relatively late, but there are remedies. Generally, manual taps can be used to repair.
스틸 드럼 플랜지 나사의 수동 수리 방법
Under normal circumstances, when the thread damage is not very heavy, it is easiest to use a manual tap to repair.
I Preparation of tools
1. Purchase thread taps suitable for drum flanges. Standard closed steel drum flange, the large flange is G2 pipe thread, the small flange is G3/4 pipe thread, and taps are purchased according to the standard. The following figure shows common tap shapes. If you are not sure what kind of tap to buy, you can contact the flange supplier, and they will definitely give you the most suitable tap.
2. In addition to buying taps, you should also buy matching tap wrenches, as shown in the figure below, there are usually two types of wrenches.
3. If you use it frequently, for convenience, you can directly weld a wrench to the rear end of the tap without removing it.
II the repair method and process
실을 수리하는 것은 실제로 두드리는 과정입니다. 플랜지의 안쪽 나사산에 탭을 한 번 나사로 조이면 플랜지 안쪽 나사산의 손상된 부분이 수리됩니다.
수리할 때 탭을 플랜지 나사산에 일정한 토크로 나사로 조여 자격 있는 나사산을 빼냅니다.
수동 수리의 품질은 인적 요소의 영향을 크게 받으므로 올바른 방법을 취해야만 플랜지 나사의 수리 품질을 보장할 수 있습니다.
1. 고정 스틸 드럼
플랜지 나사 수리 과정에서 스틸 드럼은 안티 토크의 힘을 받기 때문에{0} 스틸 통이나 드럼이 고정되어 있지 않으면 탭과 함께 회전하여 나사산이 고정되지 않을 수 있습니다. 수리. 따라서 수리하기 전에 먼저 강철 드럼을 고정해야 합니다. 보통 두 사람이 함께 수리할 수도 있는데, 한 사람은 철통이 돌아가지 않도록 양손으로 잡고 다른 한 사람은 수도꼭지를 조작한다.
2. 탭의 위치
To start the repair, keep the tap straight, then straighten the tap with one hand and lightly hinge the bar with the other hand. Observe whether the tap is perpendicular to the top surface of the barrel from the front or side. If necessary, it can be corrected with a ruler, so that the direction of the tap is basically correct. This process is very important, if the tap is not entered correctly, the result of the repair may be more damaging to the thread.
3. 탭 수정
수리 시작 시 탭이 올바른 위치에 있지 않으면 탭을 풀고 올바른 위치로 되돌릴 수 있습니다. 탭의 헤드가 모두 플랜지에 들어가면 더 이상 축 방향 힘을 가할 필요가 없고 나사산의 자연스러운 나사에 의존할 필요가 없습니다.
4. 탭의 안정성
The force should be uniform. When turning the wrench, the operator's two hands should be balanced. Do not use too much force and shake left and right, otherwise the thread profile will be easily torn, the threaded hole will be enlarged and the taper will be increased, and the tap will be broken.
5. Exit of the tap
렌치 헤드를 사용하여 플랜지의 모든 나사산을 통해 회전하여 탭이 느슨해지도록 한 다음 수리된 나사산과 탭 사이의 끼워맞춤이 느슨하기 때문에 역 탭의 나사를 푸십시오. 빼낼 때 탭이 흔들리거나 진동하지 않도록 하십시오. 나사산의 표면 마감이 손상될 수 있습니다.
III Matters needing attention
플랜지 나사산을 수동 탭으로 수리한 후 스틸 드럼 내부에 일부 철가루가 남을 수 있으며 이는 불가피합니다. 따라서 수리가 완료된 후에는 배럴의 청결을 보장하기 위해 배럴의 철 조각을 청소하는 효과적인 방법을 사용해야합니다.
정상적인 상황에서 배럴 플러그가 설치되면 수리된 플랜지 나사산이 일반 나사산보다 느슨해지며 이는 정상적인 현상이며 사용에 영향을 미치지 않습니다.
